Horizontal scrolling

[liangfei2021]

1. TFT LCD(ST7789P3-240*284),
2. 8 pictures(190*190) are placed horizontally in the cont
3. then use lv_obj_set_scroll_snap_x(), lv_obj_scroll_to_view() to scroll horizontally,
4. the FPS is about 10fps when scrolling, the effect is very bad!

[BanMian11]

Hello, can you share the code that drives ST7789P3.

[liangfei2021]

void st7789P3_init(void)
{
    lcd_init_cmd_t st7789P3_init_cmds[] = {
        {0xCF, {0x00, 0x83, 0X30}, 3},
        {0xED, {0x64, 0x03, 0X12, 0X81}, 4},
        {0xE8, {0x85, 0x01, 0x79}, 3},
        {0xCB, {0x39, 0x2C, 0x00, 0x34, 0x02}, 5},
        {0xF7, {0x20}, 1},
        {0xEA, {0x00, 0x00}, 2},
        {0xC0, {0x26}, 1},
        {0xC1, {0x11}, 1},
        {0xC5, {0x35, 0x3E}, 2},
        {0xC6, {0x0F}, 1},
        {0xC7, {0xBE}, 1},
        {0x36, {0x00}, 1}, // Set to 0x28 if your display is flipped
        {0x3A, {0x05}, 1},
        // {0x33, {0x00,0x46,0x00,0xD6,0x00,0x24}, 6},
        // {0x37, {0x00,0x45}, 2},
 
#if ST7789P3_INVERT_COLORS == 1
    {0x21, {0x00}, 0}, // set inverted mode
#else
    {0x20, {0x00}, 0}, // set non-inverted mode
#endif
 
        {0xB1, {0x44, 0x00,0x00, 0x14}, 3},
        // {0xB2, {0x0C, 0x0C, 0x00, 0x33, 0x33}, 5},
        // {0xB3, {0x11, 0x0F}, 2},
        {0xF2, {0x08}, 1},
        {0x26, {0x01}, 1},
        {0xE0, {0xD0, 0x00, 0x02, 0x07, 0x0A, 0x28, 0x32, 0x44, 0x42, 0x06, 0x0E, 0x12, 0x14, 0x17}, 14},
        {0xE1, {0xD0, 0x00, 0x02, 0x07, 0x0A, 0x28, 0x31, 0x54, 0x47, 0x0E, 0x1C, 0x17, 0x1B, 0x1E}, 14},
        {0x2A, {0x00, 0x00, 0x00, 0xEF}, 4},
        {0x2B, {0x00, 0x00, 0x01, 0x3f}, 4},
        {0x2C, {0x00}, 0},
        {0xB7, {0x07}, 1},
        {0xB6, {0x0A, 0x82, 0x27, 0x00}, 4},
        {0x11, {0x00}, 0x80},
        {0x29, {0x00}, 0x80},
        {0x00, {0x00}, 0xff},
    };
 
    //Initialize non-SPI GPIOs
    gpio_pad_select_gpio(ST7789P3_DC);
    gpio_set_direction(ST7789P3_DC, GPIO_MODE_OUTPUT);
 
#if !defined(CONFIG_LV_DISP_st7789P3_SOFT_RESET)
    gpio_pad_select_gpio(ST7789P3_RST);
    gpio_set_direction(ST7789P3_RST, GPIO_MODE_OUTPUT);
#endif
 
#if ST7789P3_ENABLE_BACKLIGHT_CONTROL
    gpio_pad_select_gpio(ST7789P3_BCKL);
    gpio_set_direction(ST7789P3_BCKL, GPIO_MODE_OUTPUT);
#endif
 
    //Reset the display
#if !defined(CONFIG_LV_DISP_st7789P3_SOFT_RESET)
    gpio_set_level(ST7789P3_RST, 0);
    vTaskDelay(100 / portTICK_RATE_MS);
    gpio_set_level(ST7789P3_RST, 1);
    vTaskDelay(100 / portTICK_RATE_MS);
#else
    st7789P3_send_cmd(st7789P3_SWRESET);
#endif
 
    printf("ST7789 initialization.\n");
 
    //Send all the commands
    uint16_t cmd = 0;
    while (st7789P3_init_cmds[cmd].databytes!=0xff) {
        st7789P3_send_cmd(st7789P3_init_cmds[cmd].cmd);
        st7789P3_send_data(st7789P3_init_cmds[cmd].data, st7789P3_init_cmds[cmd].databytes&0x1F);
        if (st7789P3_init_cmds[cmd].databytes & 0x80) {
                vTaskDelay(200 / portTICK_RATE_MS);
        }
        cmd++;
    }
 
    st7789P3_enable_backlight(true);
 
    st7789P3_set_orientation(CONFIG_LV_DISPLAY_ORIENTATION);
}

[liangfei2021]

void st7789P3_flush(lv_disp_drv_t * drv, const lv_area_t * area, lv_color_t * color_map)
{
    uint8_t data[4] = {0};
 
    uint16_t offsetx1 = area->x1;
    uint16_t offsetx2 = area->x2;
    uint16_t offsety1 = area->y1;
    uint16_t offsety2 = area->y2;
 
#if (CONFIG_LV_TFT_DISPLAY_OFFSETS)
    offsetx1 += CONFIG_LV_TFT_DISPLAY_X_OFFSET;
    offsetx2 += CONFIG_LV_TFT_DISPLAY_X_OFFSET;
    offsety1 += CONFIG_LV_TFT_DISPLAY_Y_OFFSET;
    offsety2 += CONFIG_LV_TFT_DISPLAY_Y_OFFSET;
 
#elif (LV_HOR_RES_MAX == 240) && (LV_VER_RES_MAX == 240)
#if (CONFIG_LV_DISPLAY_ORIENTATION_PORTRAIT)
    offsetx1 += 80;
    offsetx2 += 80;
#elif (CONFIG_LV_DISPLAY_ORIENTATION_LANDSCAPE_INVERTED)
    offsety1 += 80;
    offsety2 += 80;
#endif
#endif
 
    /Column addresses/
    st7789P3_send_cmd(ST7789P3_CASET);
    data[0] = (offsetx1 >> 8) & 0xFF;
    data[1] = offsetx1 & 0xFF;
    data[2] = (offsetx2 >> 8) & 0xFF;
    data[3] = offsetx2 & 0xFF;
    st7789P3_send_data(data, 4);
 
    /Page addresses/
    st7789P3_send_cmd(ST7789P3_RASET);
    data[0] = (offsety1 >> 8) & 0xFF;
    data[1] = offsety1 & 0xFF;
    data[2] = (offsety2 >> 8) & 0xFF;
    data[3] = offsety2 & 0xFF;
    st7789P3_send_data(data, 4);
 
    /Memory write/
    st7789P3_send_cmd(ST7789P3_RAMWR);
 
    uint32_t size = lv_area_get_width(area) * lv_area_get_height(area);
 
    st7789P3_send_color((void*)color_map, size * 2);
 
}

[liangfei2021]

@BanMian11

[stale]

This issue or pull request has been automatically marked as stale because it has not had recent activity. It will be closed if no further activity occurs. Thank you for your contributions.